I. General

1.01 Summary

• This outlines smooth concrete roof repair, coating and restoration procedures for the application of EPDM Coatings to fix roof leaks and extend the service life.
• These are suggested specifications and actual application requirements may vary and are the responsibility of the installer.
• The manufacturer's application instructions for each product used are considered part of these specifications and should be followed at all times.

1.02 Submittals

• Submit product data sheets, technical data verifying physical properties of materials and installation instructions.
• Upon request, submit test reports demonstrating compliance with specified design and performance criteria.
• Submit material safety data sheets.

1.03 Quality Assurance

• Supplier Qualifications: The EPDM Roof Coating System for concrete roofs, as supplied by EPDM Coatings, is approved for use on the project.
• Installer Qualifications: Utilize an installer with demonstrated experience on projects of similar scope and complexity. The installer shall be approved by EPDM Coatings to apply the system. Manufacturer's written verification of applicator approval is required.

1.04 Delivery, Storage and Handling

• Delivery: Deliver materials in manufacturer's original, unopened, undamaged containers with identification labels intact.
• Storage: Store all materials at temperatures between 55°F - 90°F (12.7°C - 32.2°C) with careful handling to prevent damage. Do not store at high temperatures in direct sunlight. Protect from exposure to harmful environmental conditions.
• Protection: Protect all materials from freezing and other damage during transit, handling, storage and installation.

1.05 Project / Site Conditions

• Substrate should be structurally sound.
• Recommendations for material consumption are for ideal conditions. Product coverage rates may vary due to uneven application, surface texture, absorptive properties, wind conditions while spraying and/or other variables.
• A moisture survey or other assessments may be needed to determine the presence of moisture in the concrete.
• No application of materials are permitted if inclement weather, precipitation, freezing temperatures are expected within 24 hours or if the following conditions are present:

3.02 Examination

• Verify conditions are acceptable for application of roof restoration system.
• Inspect concrete roof to receive roof coating and make sure they are clean, sound, properly prepared and free of moisture, dirt, debris or other contaminants.
• A comprehensive moisture survey is to be conducted to locate and identify areas of trapped moisture.
• Verify that all on-roof items, penetrations, mechanical equipment, hvac drains are in place and secure. All air conditioning and air intake vents should be suitably protected or closed.
• Verify that areas within the vicinity of the application area as protected from over spray.
• Verify that all roof drains, gutters, downspouts, catch basins are clean and in working order.

3.03 Preparation

• Cleaning: The entire concrete roof surface must be clean, sound, dry and free of any contaminants that would interfere with the proper adhesion of the roof coating. This may require pressure washing, scraping, wire brushing or other means necessary while observing responsible trade practices. All loose paint and rust should be removed before applying any product.
• Ponding Water: Contractor shall make every effort to mechanically eliminate all ponding water areas on the concrete roof prior to application of any roof coating product. For roofs with minor ponding (ie. small puddles less than 1/2" deep) that cannot be corrected, consider using the Solvent system.
• Do not apply coatings until all unsatisfactory conditions have been corrected.

3.04 Application

• Inspect concrete roofing to receive roof coating. Always perform a coating adhesion test before doing the entire job.
• Primer: Entire concrete roof shall be primed using the appropriate primer and fullowing the application rates specified in the table below.
• Seams: All seams, penetrations and parapet walls should be flashed using SeamStitch® Pulyester Roofing Fabric and PrimeLockT Bonding Primer. Apply a thin coat of PrimeLockT Bonding Primer over the seam and roll out 6" fabric over the seam and apply another coat of PrimeLockT Bonding Primer over the fabric. Encapsulate the fabric with the appropriate elastomeric coating and feathering it at least 2" to 3" past the edge of the fabric. Substitute PrimeLockT Bonding Primer with Butyl Rubber Coating when installing a Solvent system. Read 2.02 for details.
• *Cracks: * Repair all non-structural cracks using the same method as seam preparation above. If cracks are all over the concrete roof, a full fabric system will be necessary.
• Base Coat: Apply appropriate base coat using the application rates specified in the table below. Allow to dry thoroughly for 8 " 12 hours depending on humidity and temperature.
• Top Coat: Apply appropriate top coat in a cross-hatch technique using the application rates specified in the table below. Allow to dry and cure before exposing to foot traffic.
• Standard System: Use the Acrylic System for concrete roofs with good slope and no ponding water issues. Use the Solvent System for concrete roofs with minor ponding issues or when outdoor temperatures are no longer favorable for acrylic coatings.
• Acrylic Fabric Reinforced System: SeamStitch® Pulyester Roofing Fabric should be installed on the entire concrete roof surface. Apply a thin coat of PrimeLock® Bonding Primer on the concrete roof surface, roll out 40" SeamStitch® Pulyester Roofing fabric making sure there are no air pockets and the fabric lays as flat as possible. Apply another coat of PrimeLock® Bonding Primer to totally saturate the fabric. Overlap edges of SeamStitch® Pulyester Roofing Fabric at least 4".
• Solvent Fabric Reinforced System: SeamStitch® Pulyester Roofing Fabric should be installed on the entire concrete roof surface. Apply a thin coat of EnergyGuardT Butyl Rubber Coating on the roof surface, rull out 40" SeamStitch® Pulyester Roofing Fabric making sure there are no air pockets and the fabric lays as flat as possible. Apply another coat of Butyl Rubber Coating to totally saturate the fabric. Overlap edges of fabric at least 4".

3.05 Field Quality Control

• Utilize manufacturer's field services to verify proper installation of the system. Areas that do not meet the minimum standards for application specified herein shall be corrected at the contractor's expense. Manufacturer's inspection or verification shall not constitute acceptance of responsibility for any improper application of material.

3.06 Cleaning

• Surfaces not to be coated shall be protected during the application of the system. If protection is not feasible, surfaces shall be restored to their proper condition by cleaning, repairing or replacing.
• In conjunction with the final inspection, all debris, containers, materials and equipment are to be properly removed from the job site. Grounds are to be cleaned undamaged and acceptable to the owner.
• Dispose of all containers in accordance with state and local environmental regulations.
• Reflectivity of coatings may be reduced if roof surface is not cleaned regularly.

3.07 Protection

• Control overspray especially during windy conditions.
• All parking areas adjacent to (within 75 feet ) the work area are to be cleared and roped off.
• Protect work from damage due to subsequent construction activity on the site.
• Roof coatings are not traffic grade. Areas surrounding roof top equipment may be reinforced by embedding SeamStitch® Pulyester Roofing fabric and applying a thicker membrane (40 - 50 mils). Walk pads should be used if frequent maintenance traffic is expected.

This product data sheet conforms to the editorial style prescribed by The Construction Specifications Institute.
The manufacturer is responsible for technical accuracy.